313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity pth12010 12 vin single output special features ? 12 a output current ? 12 v input voltage ? wide-output voltage adjust ? 1.2 vdc to 5.5 vdc for suffx w and 0.8 vdc to 1.8 vdc for suffx l ? auto-track? sequencing* ? margin up/down controls ? effciencies up to 94% ? output on/off inhibit ? output voltage sense ? point-of-load-alliance (pola) compatible ? available rohs compliant ? 2 year warranty total power: 66w # of outputs: single safety ul/cul can/csa-c22.2 no. 60950-1-03/ul 60950-1, file no. e174104 tv product service (en60950) certifcate no. b 04 06 38572 044 cb report and certifcate to iec60950, certifcate no. us/8292/ul ? ? ? rev. 2.16.09_115 pth12010 series 1 of 6 input input voltage range: (see note 3) 10.8 - 13.2 vdc input current: no load 10 ma typ. remote on/off: (see note 1) positive logic start-up time: 1 v/ms undervoltage lockout: 9.0 - 9.5 v typ. track input voltage: pin 8 (see note 6) 0.3 vin output voltage adjustability: (see note 4) suffx -w suffx -l 1.2 - 5.5 vdc 0.8 - 1.8 vdc setpoint accuracy: 2.0% vo line regulation: 10 mv typ. load regulation: 12 mv typ. total regulation: 3.0% vo minimum load: 0 a ripple and noise: 20 mhz bandwidth 25 mv pk-pk temperature co-effcient: -40 c to +85 c 0.5% vo transient response: (see note 5) 70 s recovery time overshoot/undershoot 100 mv margin adjustment: 5.0% vo specifcations all specifcations are typical at nominal input, full load at 25 c unless otherwise stated cin = 560 f, cout = 0 f *auto-track? is a trade mark of texas instruments
rev. 2.16.09_115 pth12010 series 2 of 6 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 environmental specifcations thermal performance: operating ambient, temperature non-operating -40 c to +85 c -40 c to +125 c msl (z suffx only) jedec j-std-020c level 3 emc characteristics electrostatic discharge: en61000-4-2, iec801-2 conducted immunity: en61000-4-6 radiated immunity: en61000-4-3 general specifcations effciency: see tables on page 3 insulation voltage: non-isolated switching frequency: suffx -w suffx -l 300 khz to 400 khz 200 khz to 300 khz approvals and standards: en60950, ul/cul60950 material fammability: ul94v-0 dimensions: (l x w x h) 34.80 x 15.75 x 9.00 mm 1.370 x 0.620 x 0.354 in weight: 5g (0.18 oz) mtbf telcordia sr-332 7,092,000 hours protection short circuit: auto reset 20 a typ.
rev. 2.16.09_115 pth12010 series 3 of 6 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 p t h 1 2 0 1 0 w a s t part number system with options product family point of load alliance compatible the ultra-wide output voltage trim range offers major advantages to users who select the pth12010. it is no longer necessary to purchase a variety of modules in order to cover different output voltages. the output voltage can be trimmed in a range of 1.2 v to 5.5 v for suffx w and 0.8 vdc to 1.8 vdc for suffx l. when the pth12010 converter leaves the factory the output has been adjusted to the default voltage of 1.2 v for the pth12010w and 0.8 v for PTH12010L. output voltage adjustment of the pth12010 series output current 01 = 12 a packaging options no suffx = trays t = tape and reel (7) input voltage 12 = 12 v mechanical package always 0 output voltage code w = wide, l = low voltage pin option a = through-hole std. pin length (0.140) a = surface-mount tin/lead solder ball mounting option (8) d = horizontal through-hole (rohs 6/6) h = horizontal through-hole (rohs 5/6) s = surface-mount solder ball (rohs 5/6) z = surface-mount solder ball (rohs 6/6) ordering information output power (max) input voltage output voltage output currents efficiency (max) regulation m odel numbers odel numbers (8, 9) min max line load 66 w 10.8 - 13.2 vdc 0.8 - 1.8 vdc 0 a 12 a 89% 10 mv 12 mv PTH12010L 66 w 10.8 - 13.2 vdc 1.2 - 5.5 vdc 0 a 12 a 94% 10 mv 12 mv pth12010w effciency table - pth12010w (i o = 8 a) output voltage effciency vo = 5.0 v 94% vo = 3.3 v 93% vo = 2.5 v 91% vo = 2.0 v 90% vo = 1.8 v 89% vo = 1.5 v 88% vo = 1.2 v 86% effciency table - PTH12010L (i o = 8 a) output voltage effciency vo = 1.8 v 89% vo = 1.5 v 88% vo = 1.2 v 86% vo = 1.0 v 84% vo = 0.8 v 82% notes 1 remote on/off. positive logic on: pin 3 open; or v > vin - 0.5 v off: pin 3 gnd; or v < 0.8 v (min - 0.2 v). 2 see figures 1, 2 and 3 for safe operating curves for the pth12010w and figures 6 and 7 for PTH12010L. 3 a 560 f electrolytic input capacitor is required for proper operation. the capacitor must be rated for a minimum of 800 ma rms of ripple current. 4 an external output capacitor is not required for basic operation. adding 330 f of distributed capacitance at the load will improve the transient response. 5 1 a/s load step, 50 to 100% i omax , c out = 330 f. 6 if utilized vout will track applied voltage by 0.3 v (up to vo set point). 7 tape and reel packaging only available on the surface-mount versions. 8 to order pb-free (rohs compatible) surface-mount parts replace the mounting option s with z, e.g. pth12010waz. to order pb-free (rohs compatible) through-hole parts replace the mounting option h with d, e.g. pth12010wad. 9 notice: some models do not support all options. please contact your local emerson network power representative or use the on-line model number search tool at http://www.powerconversion.com to fnd a suitable alternative.
rev. 2.16.09_115 pth12010 series 4 of 6 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 pth12010w characteristic data temperature (oc) nat conv 100 lf m 200 lf m 400 lf m output current (a) 20 30 40 50 60 70 80 9 0 0 2 4 6 8 1 0 1 2 temperature (oc) nat conv 100 lf m 200 lf m 400 lf m output current (a) 20 30 40 50 60 70 80 9 0 0 2 4 6 8 1 0 1 2 figure 2 - safe operating area vin = 12 v, output voltage = 3.3 v (see note a) figure 1 - safe operating area vin = 12 v, output voltage = 5 v (see note a) efficiency (%) output current (a) 5.0v 3.3v 2.5v 2.0v 1.8v 1.5v 40 50 60 70 80 90 100 0 2 4 6 8 1 0 12 1.2v vout figure 4 - efficiency vs load current vin = 12 v (see note b) temperature (oc) nat conv 100 lf m 200 lf m 400 lf m output current (a) 20 30 40 50 60 70 80 9 0 0 2 4 6 8 1 0 1 2 figure 3 - safe operating area vin = 12 v, output voltage 1.8 v (see note a) track 8 9 10 pth12010 (top view) margin up margin down 5 4 3 6 7 2 1 gnd gnd c in 560f (required) + v in inhibit c out 330f (optional) + r set 1%, 0.1w (required) v out v o se nse l o a d figure 5 - standard application notes a soa curves represent the conditions at which internal components are within the emerson network power derating guidelines. b characteristic data has been developed from actual products tested at 25 c. this data is considered typical data for the converter.
rev.mm.dd.yy short title of product 5 of x embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 rev. 2.16.09_115 pth12010 series 5 of 6 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 PTH12010L characteristic data efficiency (%) output current (a) 1.8v 1.5v 1.2v 1.0v 0.8v 50 60 70 80 90 100 0 2 4 6 8 10 vout 12 temperature (oc) output current (a) 20 30 40 50 60 70 80 90 0 2 4 6 8 10 nat conv 100 lf m figure 7 - efficiency vs load current vin = 12 v (see note b) figure 6 - safe operating area vin = 12 v, output voltage 1.8 v (see note a) track 8 9 10 pth12010 (top view) margin up margin down 5 4 3 6 7 2 1 gnd gnd l o a d c in 560f (required) + v in inhibit c out 330f (optional) + r set 1%, 0.1w (required) v out v o se nse figure 8 - standard application notes a soa curves represent the conditions at which internal components are within the emerson network power derating guidelines. b characteristic data has been developed from actual products tested at 25 c. this data is considered typical data for the converter.
0.070 (1.78) (s tando ff should er ) lowe st component 0.010 min. (0.25) bo ttom side cl ea ranc e to p vi ew si de vi ew 1.370 (34.80) 0.620 6 7 3 5 4 10 9 8 1 2 max . 0.350 (8.89) ho st boar d (15.75) ? 0.040 (1.02) 5 pl ac es 0.375 (9.52) 0.125 (3.18) 0.625 (15.88) 0.125 (3.18) (1.52) 0.060 (12.70) 0.500 (1.52) 0.060 (3.55) 0.140 dime nsions in inches (mm) t ole ranc es (unless othe rw ise specified) 2 pl ac es 0.030 ( 0.76) 3 pl ac es 0.010 ( 0.25) to p vi ew 1.370 (34.80) 0.620 6 7 3 5 4 10 9 8 1 2 (15.75) 0.375 (9.52) 0.125 (3.18) 0.625 (15.88) 0.125 (3.18) (1.52) 0.060 (12.70) 0.500 (1.52) 0.060 dime nsions in inches (mm) t ole ran ce s (unless o the r wise specified ) 2 p lace s 0.030 ( 0.76) 3 p lace s 0.010 ( 0.25) ho st boar d lowe st c ompone nt 0.010 min. (0.25) bo ttom side cl ea ranc e si de vi ew solde r ball ? 0.040 (1.02) 10 p lace s *a ft er solde r r ef lo w on c us tomer boar d 0.350 (8.89) ma x. * figure 9 - plated through-hole figure 10 - surface-mount pin connections pin no. function pin 1 ground pin 2 vin pin 3 inhibit* pin 4 vo adjust pin 5 vo sense mechanical drawings pin connections cont. pin no. function pin 6 vout pin 7 ground pin 8 track pin 9 margin down* pin 10 margin up* * denotes negative logic: open = normal operation ground = function active americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power process yellow 6 6 6 embedded power for business-critical continuity rev. 2.16.09_115 pth12010 series 6 of 6
|
